Regular price $96.00 CAD
Regular price $96.00 CAD Sale price $96.00 CAD
Sale Sold out
Shipping calculated at checkout.

Note: It is not recommended to ship emulsion when the temperature is below freezing.


TRIFECTA is a ready-to-use, extremely fast exposing and durable, violet-colored SBQ-dual cure direct emulsion for imprinted sportswear printing with water-based, discharge and plastisol inks, including post-phthalate formulations. Properly prepared, TRIFECTA stencils do not require any sensitizers or hardeners to withstand the most aggressive textile inks on the market. All the TRIFECTA stencils require to obtain durability is sufficient UV-light for exposure and post-exposure. TRIFECTA is formulated for compatibility with stationary and scanning CTS (computer-to-screen) exposure sources, including LED-based units. For maximum resolution and wider exposure latitude, yellow mesh usage is recommended with conventional exposure systems and with CTS exposure units.


TRIFECTA features fairly high viscosity (6500 centipoise at 25º C.) which provides good coating control, even on coarse mesh. Its high solids content facilitates fast drying, good buildup of EOM per coating stroke and, thus, good printed edge definition.


*In the rare cases, where 10,000 prints or more are required with aggressive inks, diazo or chemical hardening may be used.


In stock

View full details

Often Purchased With

Additional Information

  • Ultra-fast exposing
    - Suitable for CTS exposure systems
    - Good wet strength, exposure latitude, and durability
  • Easy wash-out
    - Fast stencil through-put for high volume shops
    - Suitable for automatic washout units
  • High (~43%) solids content
    - Fast drying
    - Better mesh bridging for good printed edge definition
  • High (6500 centipoise) viscosity
    - Easier to control during coating, even on coarse mesh
  • Shelf Life
    - Unopened: 1 year at 70º F (21º C)

COLOR : Violet

SOLIDS : 43%

VISCOSITY : 6500 cps

SENSITIZER : SBQ Dual-cure; Presensitized



Used or surface treated mesh need only be degreased using Magic Mesh Prep or Eco Degreaser 1:20. (Mechanical abrasion is an option for new fabric that is not surface treated. It increases the surface area of fabric for a better mechanical bond of the stencil, increasing printing run length. Abrading and degreasing can be combined in one step with Ulanogel 23.) Rinse the screen thoroughly with water. Dry the screen thoroughly.



Trifecta is pre-mixed and pre-sensitized. If needed, optional diazo (to be requested separately) can be used. For gallons –C10-D diazo, for quarts – C62 diazo can be used. \



Handle Trifecta and coated screens under yellow safe light conditions. Method 1: Utilizing thicker edge of coating through, apply two coats of emulsion on the printing side to achieve even emulsion sheeting, than one coat on the squeegee side. Dry the screen thoroughly. Method 1 due to the high solids of emulsion is sufficient for majority of printing jobs. For thicker coating use Method 2: Apply two coats on the printing side, then two coats on the squeegee side, wet-on-wet. After each coating, rotate the screen 180°. For lower Rz and sharper printing use Method 3: Follow Method 2 (above). Then, after drying the screen, apply two additional coats on the printing side, wet-on-wet.


  • Step 4: DRY THE SCREEN

Dry coated screens thoroughly in a horizontal position, printing side down, at room temperature in a dirt- and dust-free area. Use a fan to speed drying. If using a commercial dryer, dry the screen with warm, filtered air, up to 104° F. (40° C.) If humidity is above 40% RH in the room, use a dehumidifier in a drying area. Unexposed stencils have great affinity to moisture. Residual and re-absorbed moisture will prevent a screen from reacting to light properly.



Refer to the Base Exposure Table (reverse side).Base Exposure Time X Exposure Variable Factors = Approximate Exposure Time.



Make a Step Wedge Test (an instructional video for doing so is available in the “Support/Info” section of the Ulano Website: www.ulano.com) or use exposure calculator —carried through to actual printing—to determine your optimum exposure time. Optimum exposure is indicated: ■ At that exposure time when the squeegee side of the wet stencil first reaches its maximum color density and color of the stencil does not appear to be “milky” or whitish. (This is best observed while the stencil is still wet following the washout.) ■ There is no suggestion of softness or sliminess on the squeegee side emulsion after processing the stencil. ■ For water-based and discharge ink, post-expose fully developed and dry stencil from the squeegee side for the triple the time of initial optimal exposure. 



After exposure, wet both sides of the screen with a gentle spray of cold water. Then spray from the printing side until the image areas clear. Pressure washer on the fan spray of a distance about 12” off the screen from the printing side can be used to expedite the washout. Rinse both sides of the screen with a gentle spray until no soft emulsion is left on the squeegee side, and no foam or bubbles remain. Use wet vacuum to remove excess water. Dry the screen thoroughly before printing or post-exposure.


  • Step 8: BLOCKOUT and TOUCHUP

Blockout Option 1: Before drying and exposing the coated screen, use excess emulsion from the coating step to cover the blockout area. Blockout Option 2: For non-water based-inks, after exposure and washout, dry the screen. Apply Screen Filler No. 60 or Extra Heavy Blockout No. 10. Touchup Option 1: Use excess emulsion and re-expose the screen. Touchup Option 2: For non-water-based inks, use Screen Filler No. 60 or Extra Heavy Blockout No. 10 thinned with water.



Use All-Purpose Ink Wash, or the least powerful ink diluent necessary, to remove all ink remaining in the screen. Use Screen Degreaser Liquid No. 3 to help remove ink and solvent residues that might impair the action of the stencil remover. Brush Stencil Remover Liquid No. 4 or Stencil Remover Paste No. 5 on both sides of the screen. Do not let the stencil remover dry on the screen. Rinse both sides of the screen gently to avoid splash-backs, then wash the screen with a forceful spray of water. If needed, use Walk Away Haze Remover or Haze Remover Paste No. 78 to remove ink and haze residues.