19202PFXIS Epic Print Black

19202PFXIS Epic Print Black - 5 Gallon


Regular price $297.00 CAD
Regular price $330.00 CAD Sale price $297.00 CAD
Sale Sold out
Shipping calculated at checkout.

Wilflex™ Epic Print Black is a general purpose- ready to use non-phthalate ink. Epic Print Black exhibits a good balance of properties inclusive of soft hand, good color saturation, and good wash durability.


In stock


Product Resources

View full details

Additional Information

  • Enjoy long or short runs. Maintain medium to heavy body throughout the run.
  • Build-up resistant.
  • Excellent color vibrancy.
  • Easily printed with both manual and automatic presses.
  • Low cure, Fast flashing.

Fabric Types

  • 100% cotton, some blend *Not suitable for all nylon substrates. Pre-test prior to production.



  • Counts: 110 -305 t/in (43-120 t/cm)
  • Tension: 25-35 n/cm



  • Durometer: 60-80, 70/90/70
  • Edge: Square, Sharp
  • Stroke: Medium
  • *Do not use excess squeegee pressure


Non-Phthalate Stencil

  • Direct: 2 over 2
  • Capillary/Thick Film: N/A
  • Off Contact: 1/16” (.2cm) Print on contact


Flash & Cure Temperatures

  • Flash: 160-180°F (70-80°C)
  • Cure: 300°F (150°C)


Pigment Loading

  • EQ: N/A
  • MX: N/A
  • PC: N/A
  • *All percentages listed at % by weight.


Epic Additives

  • Extender: N/A
  • Reducer: Epic Viscosity Buster-1% max
  • *All percentages listed at % by weight


Shipping & Storage

  • 65-90°F (18-32°C)
  • Avoid direct sunlight.
  • Use within one year of receipt


Clean Up

  • Ink degradent or press wash
  • A heavy flood stroke that fully fills the open areas of the stencil with ink is recommended.
  • Best results achieved using recommended mesh counts.
  • For fine line graphics use 230-305 t/in (90-120 t/cm) mesh. Use 110-160 t/in mesh (43-62t/cm) as standard for large coverage and non-detailed graphics.
  • Use consistent, high-tensioned screen mesh to optimize performance properties.
  • Stir plastisols before printing.
  • Do not dry clean, bleach or iron printed area.
  • Perform fusion tests before production. Failure to cure ink properly can result in poor wash fastness, inferior adhesion and unacceptable durability. Gel and cure temperatures for ink should be measured using a Thermoprobe device placed directly in the wet ink film and verified on the substrate(s) and equipment to be used for production.
  • It is the responsibility of the printer to determine that the correct ink has been selected for a specific substrate and the application processes meet the printer’s customer standards or specifications.
  • Curing is the responsibility of each printer to confirm that the print is fully cured. PolyOne’s cure recommendations are not a guarantee or warranty, but merely suggested starting points for curing evaluations as explained above.
  • When printing on garments that contain certain dyes, you must pre-test for the potential ghosting. Please refer to our website for more information on this issue.
  • Wilflex products have been carefully designed to perform within a given viscosity range, and any dramatic change in viscosity is probable to result in a change in printing characteristics
  • NON-CONTAMINATION OF EPIC INKS: Do not mix EPIC inks with inks, additives or extenders from other companies. All buckets, palette knives, stirring apparatus, squeegees, flood bars and screens must be cleaned properly and free of phthalates and pvc containing inks. Non-phthalate emulsions and pallet adhesives must be used. Failure to follow these precautions may cause phthalate contamination in violation of consumer protection laws and regulations.
  • Any application not referred in this product information bulletin should be pre-tested or consultation sought with Wilflex Technical Services Department prior to printing.